New Posts  All Forums:Forum Nav:

The Extreme Pin Modding Guide - Page 9

post #161 of 565
2/1/06 at 2:27am
Thread Starter 
Yah, good luck timmy, post here if you have questions/concerns/problems or if you wish to gloat because it does work ; we'll try to help as much as we can .

And I'd still like to know the details on ultratobias's motherboard set up. Hell, I might tinker with some work on the PLL over spring break as I still have my 2.0GHz P-M lying around. Might as well see if I can get some life out of the ol' girl .

And no problem prona, you help a lot on the forum and post loads of good information, no reason you shouldn't be full green
Reply
Reply
post #162 of 565
2/1/06 at 2:39am
hey your turing orange
Reply
Reply
post #163 of 565
2/1/06 at 2:39am
Actually, I have a really crappy thermal grease set up, as I left the AS5 and Isopropyl alcohol at my parent's house. Next time I head home I will clean that stuff off the die and heatsink and do a better job at it.
Reply
Reply
post #164 of 565
2/1/06 at 2:59am
Quote:
Originally Posted by Moses2000
Thanks for the heads up Adrenolin. I am in Australia, and he only ships within the States. Luckily I have a sister-in-law over there, so if he is OK with shipping to her I should be in luck.

Cheers.
Just add your sisters address to your PayPal account. My father has stuff shipped to me all the time here in the States and I ship it up to him in Canada.
Reply
Reply
post #165 of 565
2/2/06 at 7:42pm
Quote:
Originally Posted by timmy223
well im prolly gonna try a 765, ive got everything possible crossed and im gonna hope for the best it will work when i do it

any luck yet?
Reply
Reply
post #166 of 565
2/2/06 at 7:46pm
well i talked to my local computer store and he said his supplier has never even heard of a 765 p-m, so i think hes smokin somthing. so i dont know what website to get it off of..any suggestions..oh and i live in canada by the way, so recommend canadian sites if you can
Reply
Reply
post #167 of 565
2/3/06 at 1:10am
ebay cheapest places to get P-Ms. I paid like $150+$11 shipping for my 745.
Reply
Reply
post #168 of 565
2/3/06 at 1:11am
well i dont think im gonna get a 765 for that much
Reply
Reply
post #169 of 565
2/3/06 at 1:12am
I got my 725 last night, installed it and its priming now. So far so good. 2.13Ghz.
Reply
Reply
post #170 of 565
2/6/06 at 9:35pm
I just pin-modded my 9300 with a 745 to 2.4GHz. It boots up fine, even plays games fine. When I run Prime95 though it returns an error after 15 minutes or so. What should I do? Will a voltage pin mod help me be stable in Prime95? Anyone lead me in the right direction? Thanks, this is my first post but I've been reading the forum for months!

BTW What software are you using to keep track of CPU and GPU temps?
Reply
Reply
post #171 of 565
2/6/06 at 11:40pm
OK, so I just voltmodded to 1.404v by grounding VID2. Ran Prime95 and it failed at 22 minutes this time. Hmmm. Maybe I'll ground VID1 and VID2 this time, pushing voltage to 1.436v. I'll report back as soon as Prime95 fails again haha.

Grounded VID1 and VID2, but now SpeedFan is reading my temperature to be 55C! It has always been about 39C or 40C before (even with the previous volt mods). I reapplied AS5 exactly as before too. What could be the problem? I am still running Prime95 on this new voltage (1.436v).
Reply
Reply
post #172 of 565
2/7/06 at 4:29pm
I was stable all night with Prime95 at 1.436v. My CPU temp (according to i9kfanGUI) stayed at around 65C while the torture test was running. As soon as the CPU load drops from 100% the temp drops to the mid 40's. Is this normal? Seems a bit hot, but my max CPU temp was 67C.
Reply
Reply
post #173 of 565
2/7/06 at 6:03pm
Yea, that's normal. you can use rmclock to drop your voltage to 1.42 and that will drop your temps a little (if its stable). Mine is stable at 1.372 (my temps hover around 60 to 61 under load). When I had my voltage at 1.404 my temps were 65-67.
Reply
Reply
post #174 of 565
2/7/06 at 6:16pm
Excuse me for my silly question... How to ground VID1 or VID 2? I saw the pinmodding guide but is there also an online photo guide for voltmodding?
Reply
Reply
post #175 of 565
2/7/06 at 6:20pm
Maybe. But it's pretty much just tweezers and a good eye!! Vid1 is the vid1 hole to a ground hole and Vid2 is the vid2 hole to a ground hole.
Reply
Reply
post #176 of 565
2/7/06 at 10:27pm

Thanks for the answer!

How do I know which one is a ground hole?

Quote:
Originally Posted by G/H
Maybe. But it's pretty much just tweezers and a good eye!! Vid1 is the vid1 hole to a ground hole and Vid2 is the vid2 hole to a ground hole.
Reply
Reply
post #177 of 565
2/7/06 at 10:47pm
Look at the diagram of the socket's pins on the first post of this thread. The black dots are grounds.
Reply
Reply
post #178 of 565
2/7/06 at 11:10pm
I got it. The ground hole is adjacent to the vid's
Reply
Reply
post #179 of 565
2/7/06 at 11:11pm

Thanks man!

I figured it out already. thanks!
Quote:
Originally Posted by TTP
Look at the diagram of the socket's pins on the first post of this thread. The black dots are grounds.
Reply
Reply
post #180 of 565
2/8/06 at 1:00am
I got a 2.0G pinmod--> 2.66G stable!!! Thanks for all you guys' help!!!
Reply
Reply
New Posts  All Forums:Forum Nav:
  Return Home