post #1 of 1
3/28/07 at 7:12pm
Thread Starter 
I've tryed to configure the wireless connection to access point, and I failed to do that.Please help...
Here goes some commands which I used to configure my eth0:

# lspci
02:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG MiniPCI Adapter (rev 05)

# modprobe ath_pci
# dmesg
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
ath_rate_sample: module not supported by Novell, setting U taint flag.
ath_rate_sample: no version for "ether_sprintf" found: kernel tainted.
ath_rate_sample: 1.2
ath_pci: 0.9.6.0 (EXPERIMENTAL)

# ifconfig eth0 up
# iwlist eth0 scan
eth0 Scan completed :
Cell 01 - Address: 00:15:E9:4B:1E:20
ESSID:"dlink"
Protocol:IEEE 802.11bg
Mode:Master
Channel:1
Encryption keyff
Bit Rate:54 Mb/s
Extra: Rates (Mb/s): 1 2 5.5 9 11 6 12 18 24 36 48 54
Quality=85/100 Signal level=-45 dBm
Extra: Last beacon: 80ms ago

So, the wireless network is exists, and it's open. I've tryed to join this network, and nothing happens:

# wpa_supplicant -Kddt -ieth0 -c /etc/wpa_supplicant.conf -Dmadwifi

Mar 29 02:09:54.891309: Initializing interface 'eth0' conf '/etc/wpa_supplicant.conf' driver 'madwifi'
Mar 29 02:09:54.891446: Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Mar 29 02:09:54.891462: Reading configuration file '/etc/wpa_supplicant.conf'
Mar 29 02:09:54.891506: Line: 1 - start of a new network block
Mar 29 02:09:54.891528: ssid - hexdump_ascii(len=5):
64 6c 69 6e 6b dlink
Mar 29 02:09:54.891556: PSK - hexdump(len=32): df 28 1c 4a ba 07 37 88 52 7e 25 7b e4 eb 89 98 af d0 12 9a ce f2 76 90 ee 64 e7 47 66 63 30 df
Mar 29 02:09:54.891595: Priority group 0
Mar 29 02:09:54.891613: id=0 ssid='dlink'
Mar 29 02:09:54.891629: Initializing interface (2) 'eth0'
Mar 29 02:09:54.894483: EAPOL: SUPP_PAE entering state DISCONNECTED
Mar 29 02:09:54.894502: EAPOL: KEY_RX entering state NO_KEY_RECEIVE
Mar 29 02:09:54.894516: EAPOL: SUPP_BE entering state INITIALIZE
Mar 29 02:09:54.894529: EAP: EAP entering state DISABLED
Mar 29 02:09:54.894573: EAPOL: External notification - portEnabled=0
Mar 29 02:09:54.894598: EAPOL: External notification - portValid=0
Mar 29 02:09:54.894664: ioctl[SIOCSIWPMKSA]: Operation not supported
Mar 29 02:09:54.894739: SIOCGIWRANGE: WE(compiled)=18 WE(source)=16 enc_capa=0x0
Mar 29 02:09:54.894755: capabilities: key_mgmt 0x0 enc 0x3
Mar 29 02:09:54.913681: Own MAC address: 00:13:ce:ee:06:9a
Mar 29 02:09:54.913778: wpa_driver_madwifi_del_key: keyidx=0
ioctl[IEEE80211_IOCTL_DELKEY]: Invalid argument
Mar 29 02:09:54.913949: wpa_driver_madwifi_del_key: keyidx=1
ioctl[IEEE80211_IOCTL_DELKEY]: Invalid argument
Mar 29 02:09:54.914072: wpa_driver_madwifi_del_key: keyidx=2
ioctl[IEEE80211_IOCTL_DELKEY]: Invalid argument
Mar 29 02:09:54.914193: wpa_driver_madwifi_del_key: keyidx=3
ioctl[IEEE80211_IOCTL_DELKEY]: Invalid argument
Mar 29 02:09:54.914313: wpa_driver_madwifi_set_countermeasures: enabled=0
Mar 29 02:09:54.936000: wpa_driver_madwifi_set_drop_unencrypted: enabled=1
Mar 29 02:09:54.936183: Setting scan request: 0 sec 100000 usec
Mar 29 02:09:54.936302: Wireless event: cmd=0x8b06 len=8
Mar 29 02:09:55.040182: State: DISCONNECTED -> SCANNING
Mar 29 02:09:55.040236: Starting AP scan (broadcast SSID)
Mar 29 02:09:55.040287: Wireless event: cmd=0x8b1a len=12

And it doesn't work... I have no idea how I can fix it. Please, help.
Reply
Reply