yup, i think i'll be heading that wayhttp://techgage.com/article/thermalt...lar_750w_psu/1
think i will be going with the 750W tooThermaltake Toughpower Modular 750W PSU Bookmark With del.icio.us Digg This Article Search With Technorati Print This Article Date:
October 4, 2006Author(s):
Power, we all need it, we all crave it and it's a part of life. Today I'm looking at an item that'll have you sounding like He-Man: "I have the power!" And you won't be wrong.Introduction
-- Select Page -- Page 1: Introduction Page 2: Closer Look Page 3: Testing, Conclusion
Thermaltake. That word is enough to make power supply purists cringe. The reason being that Thermaltake had more than a few questionable PSU's come out of it's doors over the past few years. Happily it appears that they've seen the folly of turning out questionable power supplies and have decided to turn their PSU image 180 degrees.
Enter the Toughpower line. While their old lines were made by a whole host of OEM's the Toughpower line is made by Channelwell also known as CWT. If that name means nothing to you they're the folks that did the OEM work for the likes of Antec. Antec has taken a bit of a black eye lately but it's not the fault of CWT, no instead it falls on the caps that were chosen for the PSU's used to build those units.
The caps (capacitors) in question were made by Fuhjyyu. For the topless pics we'll see if the Toughpower uses those or if that particular curse is broken.
Let's take a look and see what Thermaltake has to say about the Toughpower 750:
- Complies with ATX 12V 2.2 & EPS 12V version
- Modularized Cable Management to eliminate clutter and improve airflow inside the case
- SLI, Cross-Fire, and Dual Core CPU ready
- Next generation four +12V rails(12V1, 12V2, 12V3, 12V4) supports high-end graphic card and PC system (combined loading of 60A)
- Independent Voltage Circuit: offers unflappable current delivery under heavy load and makes voltage output more stable
- Active Power Factor Correction (PF>0.99) and high efficiency (up to 85%)
- Extremely good voltage regulation (±3%): provides steady voltage for system
- Industrial grade components (capacitor, transformer, etc)
- High reliability: MTBF>120,000 hours
- Mirror effect housing and reliable 14cm ball-bearing fan
- Protections: Over Current, Over Voltage, and Short-Circuit protection
- Safety / EMI Approvals: CE, CB, TUV, FCC, UL, CUL, and BSMI certified
ATX Logic on-off additional power rocker switch
PFC (Power Factor Correction)
14 cm Fan
SPEED: 1900 RPM (±10%)
DIMENSION: 140 X 140 X 25 mm
AIR FLOW: 82 CFM
TEMP. AUTO CONTROL
16dB at 1300RPM
P. G. Signal
Over Voltage Protection Recycle AC to Reset
+5V 7.0 Vmax
+3.3V 4.5 Vmax
+12V 15.6 Vmax
100 VAC~240 VAC
Input Frequency Range
47 ~ 63 Hz
115VAC / 10A max.
230VAC / 5A max.
up to 85%
So far the specs look pretty impressive. The rail regulation is very tight at 3%, the advertised efficiency is quite impressive if it lives up to it. Another thing worth noting is active PFC. APFC makes your wall see the PSU as a resistive device with as close to a 1 ohm load as possible. This means that the VA (volts X amperes) is as close to the wattage consumed as possible. A side benefit is that UPS's like APFC over non PFC power supplies. The power factor correction circuitry deals better with square waves.
The packaging is colorful and shows the same features and specs that are listed on Thermaltake's site along with views of the PSU.
One thing I've found that's starting to show up more and more is the handle in the top of the box. What's up with that? It's under the shrink wrap so it's not much use in the store and after the PSU is installed you're likely going to toss the box so why bother? My observation aside, inside the box resides the bundled silicone PSU isolator and the manual along with the rest of the goodies.
Don't let the labeling on the boxes fool you, there's more than one screw included with the PSU.