NotebookForums.com › Forums › General Notebook Discussions › Notebook Guides › A Photo Guide for Pin Modding 9300/XPS and Applying AS5 to GPU
New Posts  All Forums:Forum Nav:

A Photo Guide for Pin Modding 9300/XPS and Applying AS5 to GPU - Page 70

post #1381 of 1473
7/31/07 at 12:20pm
Yeah, typically the 1.6 and 1.7 can work without voltmods I believe but that doesnt seem to be the case for you.
Reply
Reply
post #1382 of 1473
8/14/07 at 4:08am
can this be done on the t5450 1.66 in the new 1720s? how hard is it too do? and is it realiable.
Reply
Reply
post #1383 of 1473
8/14/07 at 8:38am
I think it has been tried but not successful with the core 2 duos
Reply
Reply
post #1384 of 1473
8/15/07 at 1:47am
nope, it is just for the Pentium m cpu's so far
Reply
Reply
post #1385 of 1473
11/10/07 at 12:55am
wow - im going to be a cheap a$$ and do this mod - i can't believe i had my notebook for over 3 years now!

any chance i can short the mother board with this mod say if somehow the pin touches another pin?
Reply
Reply
post #1386 of 1473
11/10/07 at 3:17am
Pinmodding? I mean sure you can short anything but it would be pretty hard in this case.
Reply
Reply
post #1387 of 1473
11/10/07 at 4:35pm
Quote:
Originally Posted by zzpulp View Post
Pinmodding? I mean sure you can short anything but it would be pretty hard in this case.

okay i'm buying the pentium M 1.7 chip

2MB

- i hope i can run call of duty 4 with my 6800 overclocked - u know if i can?
Reply
Reply
post #1388 of 1473
11/10/07 at 5:36pm
I doubt it. The 6800U runs CoD2 at about 50-60 fps at 1280 x 800 in DX9 if I recall correctly. So if you are talking about a regular vanilla 6800 then it might be able to run the game but I wouldnt think the fps would be acceptable. There have to be demos you can try though.
Reply
Reply
post #1389 of 1473
1/2/08 at 7:08am
Quote:
Originally Posted by reactions View Post
okay i'm buying the pentium M 1.7 chip

2MB

- i hope i can run call of duty 4 with my 6800 overclocked - u know if i can?
Quote:
Originally Posted by zzpulp View Post
I doubt it. The 6800U runs CoD2 at about 50-60 fps at 1280 x 800 in DX9 if I recall correctly. So if you are talking about a regular vanilla 6800 then it might be able to run the game but I wouldnt think the fps would be acceptable. There have to be demos you can try though.

I ran it with PM 750 1.86Ghz + Go 6800 OC 380/700Mhz

-----------------


Between I got a big question about the pinmod. I saw some other guides and post on the same Inspiron 9300 laptop showing one is connect from C16 to B16 and other one shows C16 to C15...

Which one exactly it?

http://img134.imageshack.us/my.php?i...anchart3sj.jpg
Reply
Reply
post #1390 of 1473
1/2/08 at 11:25pm
I've done this a long time ago now, it's one of the best upgrades you can do with under a pennies cost.. Well depending on how big a piece of copper you use.
Reply
Reply
post #1391 of 1473
1/3/08 at 7:27pm
I have been running my 9300 pin/volt modded 1.8GHz @ 2.39GHz for about 2 years now. Not one problem and 100% stable.

I was very surprised at how easy it was to complete the mod and apply Artic Silver to both the CPU and GPU while in there. I used a single copper strand from some home theater speaker wire I had and it fit perfectly. Definately recommended.
Reply
Reply
post #1392 of 1473
1/27/08 at 3:19am
UPDATE!

Finally pin modded my i9300 - WEll lets say its about time!

i see a small speed boost - i did the 1.7 GHZ so my CPU says 2.26 GHZ

Can you guys help me out here - i keep getting MEDIA CENTER RECEIVER SERVICE errors - im certain it has to do with m$'s search for hardware changes - so what can i do besides reinstalling windows to stop the errors?

thanks again - it was an easy mod

OH - i freakin pullled off the battery connector to the motherboard - took a shot at using hotglue until i resoldder it tomorrow.

Thanks - appreciate the help!
Reply
Reply
post #1393 of 1473
7/13/08 at 8:41pm
I am unable to see the pictures. Does aynone know where another mod tutorial is that has viewable pictures?

Thanks

Sean
Reply
Reply
post #1394 of 1473
7/13/08 at 10:26pm
Quote:
Originally Posted by seanhobbs View Post
I am unable to see the pictures. Does aynone know where another mod tutorial is that has viewable pictures?

Thanks

Sean
Why can't you see the pictures?
Reply
Reply
post #1395 of 1473
7/14/08 at 2:51am
they are not there, all i see are black lines where the pics are supposed to be. if i click on one, i get an error.
Reply
Reply
post #1396 of 1473
7/14/08 at 3:57am
I get the same black lines, photo's are not showing up on my end.
Reply
Reply
post #1397 of 1473
7/14/08 at 8:51am
they work for me. what browser you guys using?
Reply
Reply
post #1398 of 1473
7/16/08 at 4:55pm
I dont think its a browser issue Steve. The pics are showing up as black lines for me too, and when I click on them I get this error message from the fourm

Quote:
TwilightVampire, you do not have permission to access this page. This could be due to one of several reasons:

1. Your user account may not have sufficient privileges to access this page. Are you trying to edit someone else's post, access administrative features or some other privileged system?
2. If you are trying to post, the administrator may have disabled your account, or it may be awaiting activation.
Reply
Reply
post #1399 of 1473
7/20/08 at 2:02pm
pics are not working for me either, just those black lines
Reply
Reply
post #1400 of 1473
8/29/08 at 8:02am
No pics in the first page...

Is there any possibility to find them somewhere?
Reply
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Notebook Guides
NotebookForums.com › Forums › General Notebook Discussions › Notebook Guides › A Photo Guide for Pin Modding 9300/XPS and Applying AS5 to GPU